Common Diseases and Treatments of Tomatoes

Several diseases that often occur during the growth of tomatoes include late blight, early blight, powdery mildew, gray mold, and grey leaf spot.
I. Late blight Late blight is a kind of sexual disease with low temperature and high temperatures. It is easy to prevail in the season when the temperature difference between early spring and late fall is large. This disease is harmful during the entire growth period of tomatoes. The bacteria infested seedlings, leaves, stems and fruits. With leaves and fruits most affected. Generally from the front of the shed to the onset of disease, first invade the leaves and young fruit, and gradually spread to the stems and petioles to make it dark brown. Remedy: Control the epidemic rate with 25% amidoxime suspension 1500 times, or use 72% Kangling WP 600 times, or 69% Anke WP 600 times.
Second, the early symptoms of early blight is mainly infected with leaves, stems and fruits. In general, the blade suffers serious damage. It appears as a small black spot like a needle tip, and it is constantly expanded into a rostral spot. There are more light green or yellow halos on the edges, and the surface of the circle is slightly hollowed to oval or shuttle lesions. There are thorn-like irregularities in the affected part and moldy parts in the lesion when wet. Treatment methods; can be used 10% Amisida 1500 times, or leveptin 1000 times spraying or spraying and smearing the disease, especially the infected parts of the infected parts of the shank parts to better apply the disease.
Third, powdery mildew Powdery mildew generally occurs in the late growth period, starting from the middle and lower leaves began to feel sick, early in the leaves with white spots, and then formed in the leaves of irregular sizes of white mold layer lesions. In severe cases, the leaves are covered with white powder, until the leaves are dry. Remedy: Use 25% Amistar 1500x, or 30% Teflon WP 2000x.
Fourth, gray mold Gray mold began from the edge of the tip of the leaf, the typical v-shaped lesions spread inward, while harming flowers and fruits. After the fruit is infected in the flowering period, the pathogen remains on the stigma, or on the petals and then spreads to the green fruit, fruit surface, and fruit stalk. The susceptible fruit is grayish white, soft rot, and grows a large number of gray green mold layers.
Fifth, gray leaf spot leaf spot disease is also called brown spot. It mainly damages the leaves, and it also harms the petiole when it is severe. At the beginning of the disease, the foliage was covered with light brown dots. The middle of the lesion was gray-brown to yellow-brown. The edges of the lesions were yellow-brown halo and the lesions were sunken. Later lesions were easily perforated. Treatment methods: Due to its sudden onset of disease, it is recommended that the use of 25% Amizyme suspension 1500 times liquid for prevention will have very good results. Can also be used 75% Dakkoning WP 600 times, or 25% Caesar Emulsion 1500 times, or 6% more than 1500 times the plough wettable powder spray.
In the process of planting, the above diseases often occur. It is hoped that the majority of vegetable farmers will actively seek early detection and early prevention so as to reduce unnecessary economic losses.

The piston is one of the main moving parts of the engine, is composed of combustion chamber components.
The pressure of the gas piston through the connecting rod to the crankshaft, realize the change from heat energy to mechanical energy.
The work condition is very bad, and the temperature of 1400-1800 DEG C, and pressure
Up to 13MPa above the gas contact, greatly alternating thermal stress and mechanical stress.
And by the serious corrosion of gas, and under the condition of boundary lubrication and cylinder wall friction and strong impact 1 times.
The piston in high temperature, high pressure, strong corrosive gas contact so that it has enough strength and hardness,
Heat resistance and good thermal resistance, high fatigue strength and corrosion resistance. For high speed diesel Engine Piston also requires light as far as possible.
In order to reduce the inertia force.
Marine piston large low speed diesel engine of the crosshead is usually combined.
The heat treatment process by normalizing and annealing, and iron pearlite are ferrite organization, has good heat resistance.
Piston alloy quenched and tempered steel has better heat resistance and corrosion resistance. The skirt with nodular cast iron annealing treatment, with good wear resistance.

Engine Piston Parts

Engine Piston Parts,Engine Parts ,Car Engine Parts,Parts Of Engine,Piston Engine Parts

ZhouShan HeCheng Machinery Co., LTD. , https://www.hcmarineparts.com