Packing group strapping machine is a very important equipment for packing section. It is a relatively high technical content equipment, and it is also a very easy to fault equipment. It is used in the production process, and it is quickly processed. The failure is directly related to the failure rate of the packaging segment and the quality of the packaging. Therefore, in the process of operating the strapping machine, we must learn how to use the strapping machine and quickly eliminate the general faults that occur in the strapping machine.
Amy Jiejie has summed up a large number of mechanical repair and troubleshooting experience through years of after-sales service to customers of various specifications and import and export strapping machines. The following four points are summarized:
1. Before starting the machine, it is necessary to check whether the photocell of the strapping machine is intact, whether the reflector is aligned and whether there is dust on the top, and if it is not right, it is in the correct position to remove the dust.
Whether the screws and nuts of each component are loose or not, should be tightened in time. If there is a shortage of nails and caps, the repairman must be notified to handle them in time. Check for any foreign matter in the belt rail. If it is necessary to remove it, blow out the dust in the belt rail with compressed air. Check if the crankshaft part is short of oil. If it is missing, the crankshaft must be refueled by trickle-drop method, usually with a small stick of oil, slowly dripping on the shaft, and can not be inverted to the belt rail. Slip when you play, don't take the belt, don't hit the belt. If abnormal phenomena are found during the booting process, such as loud sound, large vibration, and odor, if you can't find it yourself, you should stop the repairman to deal with it, so as not to cause damage to internal parts.
Second, the quality of the straps on the quality of the packaging
In the production process, due to the density of the incoming materials, equipment failure, human factors, etc., the straps are unstable after the manufacture of the straps, and the following cases often occur, the thickness is uneven, and the width and unevenness are uneven. ,rough surface. In the process of packing, there is a phenomenon that the belt cannot be hit, the belt is not tight, the cassette is stuck, and the like. It directly affects the progress of production and the downtime of the package group. The above general treatment method is to first check whether it is a device or a belt. When the inspection confirms that it is the cause of the belt, if the thickness is uneven, the width and the unevenness are found, the binding has quality problems. It is necessary to cut off the unqualified part and not use it. If you try to hit it, if you can't hit the belt, adjust the elastic button on the strapping machine until the belt is adjusted to meet the craft standard. quasi. Unstable quality of the belt can also cause difficulty in feeding, or can not directly enter the belt, and even cause a jam. If most of the tapes do not meet the quality standards, then a new bundle will be tested. Therefore, our company strongly recommends that you use the Amyjie brand packing belt, with quality and quality assurance and good after-sales service.
Third, the elimination of common faults
1. The cigarette packs in the production run directly without hitting, or one of them does not hit. The photocell and the reflector should be checked for alignment and should be aligned if not aligned. If there is damage, notify the electrician to replace it.
2. The cigarette pack is not in the position of the belt. The method of treatment is to check if the soldering iron temperature regulator is at the required temperature position, usually at a temperature of 300C. It can be adjusted between plus and minus 10C according to the temperature of the environment. If the temperature is too high, it will be easily broken after being thinned, and the temperature will be too low to stick to the belt. Check if the belt is loose. Generally, if the nut is loose, the nut will fall off. The loose belt will cause the belt to slide out to the side and cannot reach the standard position, so that it cannot be hit. The cassette is also a very common problem. During the booting process, the strap is stuck in the feeding track due to improper operation or the belt is out of specification. This requires removing the baffle plate beside the feed rail, and pulling out the jammed tape, and blowing out the residual portion of the remaining inner strap and dust with compressed air.
Fourth, change the strap
Change the straps to do it, don't panic, calm and stable. When the strap is still enough to hit 2-3 packs, the strap is taken off the strap rack and placed next to it, which is beneficial to have a certain time to replace the newly-changed strap without affecting normal production. After the replacement, put the belt in order, and finish the remaining one roll, usually the last one will prevail. Routine savings, eliminate waste. Put on the newly-fitted strap and complete the strap change process. If the new belt is replaced, there will be looseness and unevenness. The elastic button should be adjusted in time until it meets the technical standards. The straps should be adjusted to be moderate, too tight to be able to hit the belt, too loose and not in line with the process requirements. Must be adjusted to meet the process standards, but also to ensure that the success rate of the tape is good.